| |
|
|
| |
HRCJDY-BZ標準雷電脈沖沖擊電壓校準測試系統裝置 |
|
| |
|
|
| |
本標準校驗檢定測試系統裝置由：標準沖擊電壓表、標準沖擊電壓分壓器、示波器、計算機記錄測量分析軟件及測試附件組成。是校準驗證鑒定檢定雷電沖擊電壓發生器、雷電脈沖電壓發生器、單次和連續脈沖電壓發生器、雷擊浪涌發生器、雷電沖擊電流發生器、雷電脈沖電流發生器、單次和連續脈沖電流發生器、用于其他行業專業領域的雷電沖擊耐壓試驗儀、雷電沖擊耐流試驗儀、脈沖沖擊耐壓試驗儀、脈沖沖擊耐流試驗儀和其他類型的電子脈沖發生器等等的充電電壓和輸出的電壓或者電流的準確精度的等級、分壓比或者分流比的檢測標定和誤差范圍的檢測的標準校驗檢測裝置。在1994年8月19日，我公司在中國雷電脈沖沖擊試驗檢測校驗裝置的研制生產成功并送檢計量溯源中國國家高電壓計量站，雷電沖擊計量鑒定檢定檢測試驗一次性成功---獲取校準報告！
本標準校驗檢定測試系統裝置：各個單元單體小，都是便攜式，重量輕，組合式，穩定重復性好，抗干擾能力極強，現場使用適應性好，隨時隨地就可以建立組成標準校驗檢定測試系統進行校正校準。
|
|
| |
|
|
| |
1、HRHG-23B型 標準雷電脈沖沖擊峰值電壓表 |
|
| |
HRHG-23B型標準雷電脈沖沖擊峰值電壓表：是測量任一波頭時間大于500ns單次雷電沖擊電壓全波，也可以測量和儲存雷電沖擊電壓峰值、雷電沖擊電流峰值以及其它單次雷電脈沖峰值和連續脈沖峰值，雷擊浪涌峰值、操作波峰值、陡波及截波峰值的智能型專用儀表，是為測試條件較為惡劣的高電壓試驗場所使用而專門研制的。整體設計采用標準工業控制總線特殊布線。機內設計有屏蔽、濾波以及過電壓保護電路，能有效地屏蔽很強的電磁干擾。儀表量程可自動切換，設有能換算到高壓側電壓的分壓比撥盤設定，即可直接數字讀取和顯示雷電脈沖沖擊發生器的真實輸出電壓或者電流值。便攜式。
輸入電壓：≤±1600V（雷電脈沖沖擊電壓）
輸入阻抗：2MΩ//40pF
測量精度：±1.0%
上升時間：約85ns
工作環境：-25～+55℃，0～95%
分壓比設定：0.1～9999.9
顯示范圍：0～16000kV
連接：2個插座并聯輸入
輸入電源：AC 220V 50Hz ±10％
外形結構尺寸：518長×438高×168深(mm)；
重 量： < 5kg |
|
| |
|
|
| |
|
|
| |
2、HRFY-B-1000kV/2kΩ標準純電阻型雷電脈沖沖擊電壓分壓器 |
|
| |
型 號： HRFY-B-1000/2
額定電壓： 0~100kV、0~200kV、0~400kV、0~1000kV。
輸入電壓類型： 雷電脈沖沖擊電壓
額定電阻： 2kΩ，無感，純電阻
節 數： 1節
方波響應： 部分響應時間小于100ns，過沖小于10%
分壓比： 1000:1
分壓比不確定度： ±1.0%
體積尺寸（長×寬×高）:280×280×800mm~2000mm
重量：約10kg~30kg。便攜式。
|
|
| |
|
|
| |
|
|
| |
3、HR-TDS-3012C高壓彩色數字示波器校準測試分析系統 |
|
| |
型 號： HR-TDS-3012C高壓彩色數字示波器
測量信號： 輸入0~400V
測量波形不確定度：±3.0%
體積尺寸（長×寬×高）:350×180×300mm，
重量：約3.0kg。
工作電源：AC 220V 50Hz ±10％
便攜式。
3A.波形記錄測量采集硬件：
HR-TDS-3012C高壓彩色數字示波器:
最高采樣率1.25GS/s，帶寬100MHz，分辨率9bit，
2通道測量，記錄長度10k字節（滿足雷電沖擊校驗檢測研究要求）
彩色顯示波形和多種語言菜單文字選擇；
3B.波形測量分析采樣軟件：
HR-3000B計算機雷電沖擊記錄測量分析專用軟件包：
沖擊波形參數計算及記錄顯示，波形分析比較功能
沖擊波形的放大、縮小及平移，波形的存儲及調用
沖擊波形的成圖及檢測校驗報告編寫
3C.附件：HR-100型高性能100倍專用衰減器2支。
校驗檢測和計算機通訊的線纜及附件一套。
重要說明：計算機用戶自己配備!
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
| |
HRCJDY-BZ
Standard lightning impulse voltage pulse calibration test
system devices |
|
| |
The standard calibration verification
test system device consists of : a standard impulse voltage
meter , standard impulse voltage divider , oscilloscopes,
computer records and test measurement and analysis software
accessories. Calibration verification test is to identify
lightning impulse voltage generator , lightning impulse
voltage generator , single and continuous pulse voltage
generator , lightning surge generator , lightning impulse
current generator , lightning impulse current generator
, single and continuous pulse current generator , lightning
impulse withstand voltage tester for other areas of industry
professionals , the lightning impulse flow resistance tester
, pulse-pounding pressure tester , impact -resistant pulsed
flow tester and other types of electronic pulse generator
charging voltage , etc. and the output voltage or current
accuracy level of accuracy , or the partial pressure ratio
of the flow ratio of the detection range of the calibration
and error detecting means detects the calibration standard
. In August 19, 1994 , I was the first in China to detect
lightning impulse impact test calibration device and starting
to develop and produce a successful submission metrological
traceability Chinese national high voltage metering station
, lightning impulse measurement identification verification
testing disposable success --- Get calibration report !
The standard calibration verification test system devices:
small individual monomer units are portable , lightweight
, modular , stable and reproducible, anti-interference ability
, adaptability field use , anytime, anywhere can create
a standard school composition test test test system calibration
calibration.
|
|
| |
|
|
| |
HRHG-23B
Standard lightning impulse voltage meter peak |
|
| |
HRHG-23B Standard lightning impulse voltage
meter peak impact : the first is to measure any wavelength
longer than 500ns single full-wave lightning impulse voltage
can also be measured and stored lightning impulse voltage
spikes , lightning impulse current peak as well as other
one-time lightning pulse peak and continuous pulse peak
, lightning surge peak operating wave peaks , steep peaks
spread chopper intelligent special instrument , is the use
of a more severe test conditions for the high-voltage test
site specially developed . The overall design using standard
industrial control bus special wiring . In the design of
the shield machine , filtering and overvoltage protection
circuit can be highly effective electromagnetic interference
shielding . Range of the instrument can automatically switch
features can be translated to the high side voltage divider
ratio dial , you can read and display lightning direct digital
pulse-pounding real value of output voltage or current generator
. Portable .
Input voltage : ≤ ± 1600V ( lightning impulse voltage pulse
)
Input impedance : 2MΩ / / 40pF
Accuracy : ± 1.0%
Rise time : about 85ns
Working environment : -25 ~ +55 ℃, 0 ~ 95%
Divider ratio setting: 0.1 to 9999.9
Display range : 0 ~ 16000kV
Connection : two parallel input socket
Input Power : AC 220V 50Hz ± 10%
Shape and size : length 518 × 168 × 438 high depth (mm);
Weight : <5kg
|
|
| |
|
|
| |
|
|
| |
HRFY-B-1000kV/2kΩ
standard lightning impulse purely resistive voltage divider
impact |
|
| |
Type: HRFY-B-1000/2
Rated Voltage: 0 ~ 100kV, 0 ~ 200kV, 0 ~ 400kV, 0 ~ 1000kV。
Input voltage type: lightning impulse voltage pulse
Rated resistance: 2kΩ, no sense, pure resistance
Sections: 1
Square wave response: partial response time less than 100ns，
the overshoot is less than 10%
Divider ratio: 1000:1
Divider ratio Uncertainty: ± 1.0%
Volume size (l × w × h): 280 × 280 × 800mm ~ 2000mm
Weight: about 10kg ~ 30kg. Portable.
|
|
| |
|
|
| |
|
|
| |
HR-TDS-3012C
high-voltage color digital oscilloscope calibration test
and analysis system |
|
| |
Model: HR-TDS-3012C high-voltage color
digital oscilloscope
Measuring signal: 0 ~ 400V input
Waveform Measurement Uncertainty: ± 3.0%
Volume size (length × width × height): 350 × 180 × 300mm，
weight: about 3.0kg.
Power Supply: AC 220V 50Hz ± 10%
Portable.
3A. waveform record measurement acquisition hardware:
HR-TDS-3012C high-voltage color digital oscilloscope:
Maximum sampling rate 1.25GS / s, bandwidth of 100MHz, resolution
9bit,
2-channel measurement, recording length 10k bytes (checksum
to detect lightning impulse to meet research requirements)
Multilingual menu color display waveforms and text selection;
3B. sampled waveform measurement and analysis software:
HR-3000B computer Impulse Records dedicated measurement
and analysis software package:
Shock wave parameters to calculate and record shows waveform
analysis and comparison function
Shock-shaped zoom in, zoom and pan, and call stored waveforms
Shock wave into the preparation and testing calibration
chart report
3C. accessories: HR-100 high-performance 100-fold dedicated
attenuator 2.
Cables and accessories parity detection and a set of computer
communication.
Important Description: with the user's own computer!
|
|
| |
|
|
| |
|
|
